Installing boot9strap (MSET9 Play Store)
Détails techniques (facultatif)
MSET9 is an exploit for the System Settings application developed by zoogie. It exploits a flaw where the ID1 (the second 32-character folder name inside of the Nintendo 3DS folder, inside of the ID0) can be any name as long as it is 32 characters. Performing a specific sequence of actions results in the console executing the instructions that are encoded into the ID1 folder name, which can be used to grant full control over the 3DS.
Notes de compatibilité
This page requires an Android phone/tablet or a Chromebook. If you have a computer running Windows, macOS, or Linux, follow Installing boot9strap (MSET9 CLI) instead. If you do not have access to any of these devices, you will need to use an alternate exploit.
On Android phones/tablets, the minimum Android version required is 6.0 (Marshmallow).
Ce dont vous avez besoin
- The following applications installed from the Google Play Store:
- MSET9 Installer
- ZArchiver
- If you wish, you can sideload these applications instead
- The latest release of MSET9 (the Release
.zipfile)
Instructions
Section I - Préparatifs
In this section, you will prepare the SD card data necessary for the MSET9 exploit to trigger.
- Power on your console with your SD card inserted
- Open Mii Maker
- Wait for your console to reach the “Welcome to Mii Maker” screen, then exit Mii Maker
- You may see this screen, which indicates the necessary data has been created
- If you just reach the normal Mii Maker screen, exit Mii Maker and continue to the next step
- Éteignez votre console
- Insert your SD card into your phone/tablet/computer
- Copy everything from the Release
.zipto the root of your SD card, overwriting any existing files:- Open ZArchiver
- If prompted, allow ZArchiver to access files on your SD card
- Navigate to where the downloaded MSET9 Release
.zipis located (likely in the Downloads folder) - Select the Release
.zip, then select “Extract…” (image) - Navigate to your SD card, then tap the blue ‘down arrow’ icon to extract the files to the root of your SD card (image)
- Run the MSET9 Installer application
- Tap on
Select "Nintendo 3DS" Folder, then navigate to yourNintendo 3DSfolder on your SD card (image) - Once inside the
Nintendo 3DSfolder, tap on “Use this folder”, then “Allow” if asked (image) - If “Setup MSET9” is highlighted, proceed to the next step. Do not setup MSET9 yet. Close the MSET9 Installer for now
- If “Check Again” is highlighted, there is a problem that you need to resolve before you can use MSET9. Refer to the troubleshooting
- Réinsérez votre carte SD dans votre console
- Power on your console
Section II - MSET9
In this section, you will trigger MSET9 to launch SafeB9SInstaller (the custom firmware installer).
These instructions must be followed EXACTLY, so double-check EVERYTHING you are doing to avoid errors!
- Hover over the System Settings icon using the D-Pad (do not select it yet)
- Power off, then power on your console
- Press (A) to launch System Settings
- Navigate to
Data Management->Nintendo 3DS->Extra Data(image) - Do not press any buttons or touch the screen
- With the console STILL ON, and without pressing any buttons or touching the screen, remove your SD card from your console
- The menu will refresh and say that no SD card is inserted, which is expected
- Insert your SD card into your phone/tablet/computer
- Open the MSET9 Installer application
- Tap “Setup MSET9”
- Tap on the photo corresponding to your console model, then on the button corresponding to your current firmware version
- If the injection was successful, all buttons should become grayed out except for “Remove MSET9”
- Reinsert your SD card into your console without pressing any buttons or touching the screen
- Si l’exploit a réussit, vous devriez avoir démarré dans SafeB9SInstaller
- If you get a red screen or the console gets stuck on a loading screen, follow the troubleshooting guide
Section III - Installation de boot9strap
In this section, you will install custom firmware onto your console.
- Lorsque vous y êtes invité, entrez la combinaison de touches indiquée sur l’écran supérieur pour installer boot9strap
- Si une étape sur l’écran du bas a du texte rouge, et que vous n’êtes pas invité à entrer une combinaison de touches, suivez ce guide de dépannage
- Once it is complete, press (A) to reboot your console
- Your console should have booted into the Luma3DS configuration menu
- Le menu de configuration de Luma3DS sert à régler les paramètres du custom firmware Luma3DS. Beaucoup de ces paramètres peuvent être utiles pour la personnalisation ou le débogage
- Pour les besoins de ce guide, laissez ces options sur les paramètres par défaut (ne cochez ni ne décochez rien)
- If your console shuts down when you try to power it on, ensure that you have copied
boot.firmfrom the Luma3DS.zipto the root of your SD card
- Appuyez sur (Start) pour enregistrer les modifications et redémarrer
Section IV - Removing MSET9
In this section, you will remove MSET9 to prevent further issues. (This will not remove the custom firmware that you just installed.)
Do NOT skip this section! If you skip it, applications may crash unexpectedly and you will encounter errors on the next page!
- Éteignez votre console
- Insert your SD card into your phone/tablet/computer
- Open the MSET9 Installer application
- Tap “Remove MSET9”
- Close the MSET9 Installer application
À partir d’ici, votre console démarrera sur Luma3DS par défaut.
- Luma3DS ne présente aucune différence visuelle avec le menu HOME normal. Si votre console a démarré dans le menu HOME, elle exécute un custom firmware.
- Sur la page suivante, vous installerez des applications homebrew utiles pour compléter votre configuration.
Did you follow Section IV (Removing MSET9)? That section is MANDATORY!