Installing boot9strap (MSET9 Play Store)

Para soporte en inglés, pide ayuda en el Discord de Nintendo Homebrew.
Si te gustó esta guía, aceptamos Donaciones.

Technical Details (optional)

MSET9 is an exploit for the System Settings application developed by zoogie. It exploits a flaw where the ID1 (the second 32-character folder name inside of the Nintendo 3DS folder, inside of the ID0) can be any name as long as it is 32 characters. Performing a specific sequence of actions results in the console executing the instructions that are encoded into the ID1 folder name, which can be used to grant full control over the 3DS.

Compatibility Notes

This page requires an Android phone/tablet or a Chromebook. If you have a computer running Windows, macOS, or Linux, follow Installing boot9strap (MSET9 CLI) instead. If you do not have access to any of these devices, you will need to use an alternate exploit.

On Android phones/tablets, the minimum Android version required is 6.0 (Marshmallow).

Qué necesitas

  • The following applications installed from the Google Play Store:
  • The latest release of MSET9 (the Release .zip file)


Sección I - Preparativos

In this section, you will prepare the SD card data necessary for the MSET9 exploit to trigger.

  1. Power on your console with your SD card inserted
  2. Open Mii Maker
  3. Wait for your console to reach the “Welcome to Mii Maker” screen, then exit Mii Maker
    • You may see this screen, which indicates the necessary data has been created
    • If you just reach the normal Mii Maker screen, exit Mii Maker and continue to the next step
  4. Apaga tu consola
  5. Insert your SD card into your phone/tablet/computer
  6. Copy everything from the Release .zip to the root of your SD card, overwriting any existing files:

    MSET9 root layout

  7. Run the MSET9 Installer application
  8. Tap on Select "Nintendo 3DS" Folder, then navigate to your Nintendo 3DS folder on your SD card (image)
  9. Once inside the Nintendo 3DS folder, tap on “Use this folder”, then “Allow” if asked (image)
  10. If “Setup MSET9” is highlighted, proceed to the next step. Do not setup MSET9 yet. Close the MSET9 Installer for now
    • If “Check Again” is highlighted, there is a problem that you need to resolve before you can use MSET9. Refer to the troubleshooting
  11. Reinsert your SD card into your console
  12. Power on your console

Section II - MSET9

In this section, you will trigger MSET9 to launch SafeB9SInstaller (the custom firmware installer).

These instructions must be followed EXACTLY, so double-check EVERYTHING you are doing to avoid errors!

  1. Hover over the System Settings icon using the D-Pad (do not select it yet)
  2. Power off, then power on your console
  3. Press (A) to launch System Settings
  4. Navigate to Data Management -> Nintendo 3DS -> Extra Data (image)
  5. Do not press any buttons or touch the screen
  6. With the console STILL ON, and without pressing any buttons or touching the screen, remove your SD card from your console
    • The menu will refresh and say that no SD card is inserted, which is expected
  7. Insert your SD card into your phone/tablet/computer
  8. Open the MSET9 Installer application
  9. Tap “Setup MSET9”
  10. Tap on the photo corresponding to your console model, then on the button corresponding to your current firmware version
    • If the injection was successful, all buttons should become grayed out except for “Remove MSET9”
  11. Reinsert your SD card into your console without pressing any buttons or touching the screen
  12. Si el exploit ha funcionado, habrás iniciado SafeB9SInstaller
    • If you get a red screen or the console gets stuck on a loading screen, follow the troubleshooting guide

Sección III - Instalar boot9strap

En esta sección, instalarás custom firmware en tu consola.

  1. Cuando se te pida, introduce la combinación de botones mostrada para instalar boot9strap
  2. Una vez completado, pulsa (A) para reiniciar tu consola
  3. Tu consola debería haber iniciado en el menú de configuración de Luma3DS
    • En el menú de configuración de Luma3DS están los ajustes para el custom firmware Luma3DS. La mayoría de estos ajustes son para customizar o para debugging
    • Para los fines de esta guía, deja estas opciones en los valores por defecto (no marques ni desmarques nada)
    • Si la consola se apaga cuando intentas encenderla, asegúrate de que copiaste boot.firm desde el archivo .zip de Luma3DS a la raíz de tu tarjeta SD
  4. Presiona (Start) para guardar y reiniciar

Section IV - Removing MSET9

In this section, you will remove MSET9 to prevent further issues. (This will not remove the custom firmware that you just installed.)

Do NOT skip this section! If you skip it, applications may crash unexpectedly and you will encounter errors on the next page!

  1. Apaga tu consola
  2. Insert your SD card into your phone/tablet/computer
  3. Open the MSET9 Installer application
  4. Tap “Remove MSET9”
  5. Close the MSET9 Installer application

En este punto, tu consola arrancará en Luma3DS por defecto.

  • Luma3DS no se ve distinto del Menú HOME normal. Si tu consola ha encendido y muestra el Menú HOME, está ejecutando custom firmware.
  • En la siguiente página, instalarás aplicaciones útiles de homebrew para completar la instalación.

Did you follow Section IV (Removing MSET9)? That section is MANDATORY!

Continúa en Finalizar instalación