Installing Boot9strap (Fredtool)
Required Reading
This method of using Seedminer for further exploitation uses your movable.sed
file to decrypt any DSiWare title for the purposes of injecting an exploitable DSiWare title into the DS Internet Settings application. This requires you to have a DSiWare backup, for example from BannerBomb or the DSiWare Dumper tool.
Esta é uma implementação funcional do exploit “FIRM partitions known-plaintext” detalhado aqui.
What You Need
- A DSiWare Backup (such as the one on SD root from BannerBomb3)
- Your
movable.sed
file from completing Seedminer - The latest release of Frogminer_save
- The latest release of b9sTool
- The latest release of Luma3DS
Section I - CFW Check
- Desligue seu dispositivo
- Hold the (Select) button
- Power on your device while still holding the (Select) button
- If the check was successful, you will boot to the HOME Menu and you may proceed with this guide
If you see a configuration menu, you already have CFW, and continuing with these instructions may BRICK your device! Follow Checking for CFW to upgrade your existing CFW.
Section II - Prep Work
- Desligue seu dispositivo
- Insira o cartão SD no seu computador
- Copy
boot.firm
andboot.3dsx
from the Luma3DS.zip
to the root of your SD card- The root of the SD card refers to the initial directory on your SD card where you can see the Nintendo 3DS folder, but are not inside of it
- Copy
boot.nds
(B9STool) to the root of your SD card -
Copy the
private
folder from the Frogminer_save.zip
to the root of your SD card
Section III - Fredtool
- Open Fredtool on your computer
- Select your
movable.sed
file for the “Your movable.sed” field - Select your DSiWare Backup (
<8-character-id>.bin
) file for the “Your dsiware.bin” field - Select “Verify files”
- Select “Build and Download”
- Wait for the process to complete
- When the process is completed, download your modified DSiWare archive from the site
- This file contains 2 DSiWare backup files, one clean (unmodified) and one hax (exploited)
- Navigate to
Nintendo 3DS
-><ID0>
-><ID1>
->Nintendo DSiWare
on your SD card- The
<ID0>
will be the same one that you used in Seedminer - The
<ID1>
is a 32 character long folder inside of the<ID0>
- If the
Nintendo DSiWare
folder does not exist, create it inside of the<ID1>
- The
- Copy the
42383841.bin
file from theoutput/hax/
folder of the downloaded DSiWare archive (fredtool.zip
) to theNintendo DSiWare
folder - Reinsira seu cartão SD no seu dispositivo
- Ligue o seu dispositivo
- Launch System Settings on your device
- Navigate to
Data Management
->DSiWare
- Under the “SD Card” section, select the “Haxxxxxxxxx!” title
- Select “Copy”, then select “OK”
- Return to main menu of the System Settings
- Navigate to
Internet Settings
->Nintendo DS Connections
, then select “OK” - If the exploit was successful, your device will have loaded the JPN version of Flipnote Studio
Section IV - Flipnote Exploit
If you would prefer a visual guide to this section, one is available here.
- Complete the initial setup process for the launched game until you reach the main menu
- Select the left option whenever prompted during the setup process
- Using the touch-screen, select the large left box, then select the box with an SD card icon
- Once the menu loads, select the face icon, then the bottom right icon to continue
- Press (X) or (UP) on the D-Pad depending on which is shown on the top screen
- Select the second button along the top with a film-reel icon
- Scroll right until reel “3/3” is selected
- Tap the third box with the letter “A” in it
- Scroll left until reel “1/3” is selected
- Tap the fourth box with the letter “A” in it
- If the exploit was successful, your device will have loaded b9sTool
- Using the D-Pad, move to “Install boot9strap”
- If you miss this step, the system will exit to HOME Menu instead of installing boot9strap and you will need to start over from Step 12 of Section III
- Press (A), then press START and SELECT at the same time to begin the process
- Once completed and the bottom screen says “done.”, exit b9sTool, then power off your device
- Você pode ter que forçar o desligamento segurando o botão power
- If you see the Luma Configuration screen, continue with the guide without powering off
Section V - Configuring Luma3DS
- Boot your device while holding (Select) to launch the Luma configuration menu
- If you encounter issues launching the Luma configuration menu, follow this troubleshooting guide
- Use o botão (A) e os botões direcionais para ativar as seguintes opções:
- “Show NAND or user string in System Settings”
- Aperte (Start) para salvar e reiniciar
At this point, your console will boot to Luma3DS by default as long as the SD card is inserted.
- Luma3DS does not look any different from the normal HOME Menu. If your console has booted into the HOME Menu, it is running custom firmware.
- On the next page, you will copy Luma3DS to internal memory so that you can boot without an SD card.
Section VI - Restoring DS Connection Settings
- Desligue seu dispositivo
- Insira o cartão SD no seu computador
- Copy the
42383841.bin
file from theoutput/clean/
folder of the downloaded DSiWare archive (fredtool.zip
) to theNintendo 3DS/<ID0>/<ID1>/Nintendo DSiWare/
folder on your SD card- Replace the existing
42383841.bin
file
- Replace the existing
- Reinsira seu cartão SD no seu dispositivo
- Ligue o seu dispositivo
- Launch System Settings on your device
- Navigate to
Data Management
->DSiWare
- Under the “SD Card” section, select the “Nintendo DSi™” title
- Select “Copy”, then select “OK”