Installing boot9strap (USM)

Aby uzyskać wsparcie w języku angielskim, wejdź na Serwer Nintendo Homebrew na Discordzie.
If you appreciate this guide, we accept Donations.

Wymagana Lektura

In order to exploit the SAFE_MODE firmware of our system, we need to inject an exploited WiFi profile.

We can do this using an existing exploit, BannerBomb3.

To accomplish this, we use your system’s encryption key (movable.sed) to build a DSiWare backup that exploits the system in order to inject the exploited WiFi profile to your connections list.

Once the WiFi profile has been injected, we will use SAFE_MODE, which is a recovery feature present on all 3DS consoles, to activate the exploited WiFi profile.

These instructions work on USA, Europe, Japan, and Korea region consoles as indicated by the letters U, E, J, or K after the system version.

If your (Right/Left Shoulder), (D-Pad Up) or (A) buttons do not work, you will need to use a Legacy Method. For assistance with this matter, join Nintendo Homebrew on Discord and ask, in English, for help.

Czego Potrzebujesz

  • Twojego pliku movable.sed z ukończenia Seedminer
  • The latest release of Luma3DS

Sekcja I - Przygotowanie

  1. If your device is powered on, power off your device
  2. Open unSAFE_MODE-bb3 tool on your computer
  3. Upload your movable.sed using the “Choose File” option
  4. Click “Download unSAFE_MODE-bb3 archive”
    • This will download an exploit DSiWare called F00D43D5.bin and a SAFE_MODE exploit data file called usm.bin inside of a zip archive (unSAFE_MODE-bb3.zip)
  5. Włóż kartę SD do komputera
  6. Copy boot.firm and boot.3dsx from the Luma3DS .zip to the root of your SD card
    • The root of the SD card refers to the initial directory on your SD card where you can see the Nintendo 3DS folder, but are not inside of it
  7. Copy usm.bin from unSAFE_MODE-bb3.zip to the root of your SD card
  8. Navigate to Nintendo 3DS -> <ID0> -> <ID1> -> Nintendo DSiWare on your SD card
    • The <ID0> will be the same one that you used in Seedminer
    • The <ID1> is a 32 character long folder inside of the <ID0>
    • If Nintendo DSiWare does not exist, create it inside of the <ID1>
  9. If there are any existing DSiWare backup files (<8-character-id>.bin) in this folder, move them to your PC
    • This will leave you with an empty Nintendo DSiWare folder. Moving the files to your PC ensures you don’t delete any intentional backups
  10. Copy the F00D43D5.bin file from unSAFE_MODE-bb3.zip to the Nintendo DSiWare folder

Section II - BannerBomb3

  1. Włóż ponownie kartę SD do konsoli
  2. Włącz konsolę
  3. Uruchom “System Settings” na twoim urządzeniu
  4. Przejdź do Data Management -> DSiWare
  5. Click on the SD Card section
    • Your bottom screen should flash Red and then the system will reboot to home menu a few seconds later. This means the exploit profile was successfully copied
    • If the bottom screen does not flash Red, the exploit profile was not copied and you will not be able to complete the next section. Ensure that your files are properly placed, then try again
  6. Wyłącz konsolę

Section III - unSAFE_MODE

  1. With your device still powered off, hold the following buttons: (Left Shoulder) + (Right Shoulder) + (D-Pad Up) + (A), then press (Power)
    • Keep holding the buttons until the device boots into Safe Mode
  2. Press “OK” to accept the update
    • There is no update. This is part of the exploit
  3. Press “I accept” to accept the terms and conditions
  4. The update will eventually fail, with error code 003-1099. This is intended behaviour
  5. When asked “Would you like to configure Internet settings?”, select “Yes”
  6. On the following menu, navigate to Connection 1 -> Change Settings -> Next Page (right arrow) -> Proxy Settings -> Detailed Setup
  7. Once you see B9S install SUCCESS on the top screen, press any button to reboot to Luma Configuration

Sekcja IV - Konfigurowanie Luma3DS

  1. Twoje urządzenie powinno uruchomić się ponownie i załadować menu konfiguracji Luma3DS
  2. Użyj przycisku (A) oraz D-Pada aby zaznaczyć:
    • “Show NAND or user string in System Settings”
  3. Naciśnij (Start) aby zapisać zmiany i uruchomić konsolę ponownie

At this point, your console will boot to Luma3DS by default as long as the SD card is inserted.

  • Luma3DS does not look any different from the normal HOME menu. If your console has booted into the HOME menu, it is running custom firmware.
  • On the next page, you will copy Luma3DS to internal memory so that you can boot without an SD card.

Section V - Restoring WiFi Configuration Profiles

  1. Uruchom “System Settings” na twoim urządzeniu
  2. Przejdź do Data Management -> DSiWare
  3. Click on the SD Card section
    • Your bottom screen should flash Green and then the system will reboot to home menu a few seconds later. This means your WiFi configuration profiles were successfully restored
  4. Wyłącz konsolę
  5. Włóż kartę SD do komputera
  6. Navigate to Nintendo 3DS -> <ID0> -> <ID1> -> Nintendo DSiWare on your SD card
  7. Delete F00D43D5.bin from your Nintendo DSiWare folder

Kontynuuj do Finalizowanie Instalacji